Strange sensors output
Mark Studebaker
mds at paradyne.com
Wed May 22 23:01:08 CEST 2002
Did sensors-detect find a w83782d?
Do you really have a w83782d (look at your board)?
send us the output of i2cdump 0 0x2d if it's not all FF's.
> Chad McKay wrote:
>
>
> This is the output from the sensors program :
> ------
> # sensors
> w83782d-i2c-0-2d
> Adapter: SMBus PIIX4 adapter at 5000
> Algorithm: Non-I2C SMBus adapter
> VCore 1: +4.08 V (min = +4.08 V, max = +4.08 V)
> VCore 2: +4.08 V (min = +4.08 V, max = +4.08 V)
> +3.3V: +4.08 V (min = +4.08 V, max = +4.08 V)
> +5V: +6.85 V (min = +6.85 V, max = +6.85 V)
> +12V: +15.50 V (min = +15.50 V, max = +15.50 V) ALARM (beep)
> -12V: +6.06 V (min = +6.06 V, max = +6.06 V) ALARM (beep)
> -5V: +5.10 V (min = +5.10 V, max = +5.10 V) ALARM (beep)
> V5SB: +6.85 V (min = +6.85 V, max = +6.85 V) ALARM (beep)
> VBat: +4.08 V (min = +4.08 V, max = +4.08 V) ALARM (beep)
> fan1: 0 RPM (min = 0 RPM, div = 128)
> fan2: 0 RPM (min = 0 RPM, div = 128)
> fan3: 0 RPM (min = 0 RPM, div = 128) ALARM
> (beep)
> temp1: -1.0°C (limit = -1°C, hysteresis = -1°C) sensor = PII/Celeron diode
> temp2: +255.5°C (limit = +256°C, hysteresis = +256°C) sensor = 3904 transistor
> temp3: +25.0°C (limit = +60°C, hysteresis = +50°C) sensor = thermistor ALARM (beep)
> vid: +0.00 V
> alarms: Chassis intrusion detection ALARM (beep)
> beep_enable:
> Sound alarm enabled
> -----
>
> None of this is anywhere near correct (obviously?).
>
> Is this a problem with my system or have I got something configured
> wrong. The first time I booted the system the speaker started beeping
> after a few seconds and never stopped - however the system runs fine
> (65 days uptime at one point). I also ran win2000 on it for about 2
> years with no problems.
>
> Thanks for your help
>
> Chad McKay
>
> Some system info:
>
> standard /etc/sensors.conf file
>
> Red Hat Linux release 7.2 (Enigma)
> Kernel 2.4.7-10smp on a 2-processor i686
>
> lm_sensors installed via RPM
> # sensors -v
> sensors version 1.3
>
> Abit bp6 MB w/ 2 clereron 366 OC @ 550 (same problems @ 366)
>
> dmesg output:
>
> Linux version 2.4.7-10smp (bhcompile at stripples.devel.redhat.com) (gcc
> version 2.96 20000731 (Red Hat Linux 7.1 2.96-98)) #1 SMP Thu Sep 6
> 17:09:31 EDT 2001
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
> BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
> BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
> Scanning bios EBDA for MXT signature
> found SMP MP-table at 000f5ae0
> hm, page 000f5000 reserved twice.
> hm, page 000f6000 reserved twice.
> hm, page 000f1000 reserved twice.
> hm, page 000f2000 reserved twice.
> On node 0 totalpages: 131056
> zone(0): 4096 pages.
> zone(1): 126960 pages.
> zone(2): 0 pages.
> Intel MultiProcessor Specification v1.1
> Virtual Wire compatibility mode.
> OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
> Processor #0 Pentium(tm) Pro APIC version 17
> Processor #1 Pentium(tm) Pro APIC version 17
> I/O APIC #2 Version 17 at 0xFEC00000.
> Processors: 2
> Kernel command line: ro root=/dev/hda2
> Initializing CPU#0
> Detected 551.260 MHz processor.
> Console: colour VGA+ 80x25
> Calibrating delay loop... 1101.00 BogoMIPS
> Memory: 510252k/524224k available (1396k kernel code, 11524k reserved,
> 102k data, 240k init, 0k highmem)
> Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
> Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
> Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
> Page-cache hash table entries: 131072 (order: 8, 1048576 bytes)
> CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
> CPU: L1 I cache: 16K, L1 D cache: 16K
> CPU: L2 cache: 128K
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
> CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
> CPU: Common caps: 0183fbff 00000000 00000000 00000000
> Enabling fast FPU save and restore... done.
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> mtrr: v1.40 (20010327) Richard Gooch (rgooch at atnf.csiro.au)
> mtrr: detected mtrr type: Intel
> CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
> CPU: L1 I cache: 16K, L1 D cache: 16K
> CPU: L2 cache: 128K
> Intel machine check reporting enabled on CPU#0.
> CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
> CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
> CPU: Common caps: 0183fbff 00000000 00000000 00000000
> CPU0: Intel Celeron (Mendocino) stepping 05
> per-CPU timeslice cutoff: 365.65 usecs.
> enabled ExtINT on CPU#0
> ESR value before enabling vector: 00000000
> ESR value after enabling vector: 00000000
> Booting processor 1/1 eip 2000
> Initializing CPU#1
> masked ExtINT on CPU#1
> ESR value before enabling vector: 00000000
> ESR value after enabling vector: 00000000
> Calibrating delay loop... 1101.00 BogoMIPS
> CPU: Before vendor init, caps: 0183fbff 00000000 00000000, vendor = 0
> CPU: L1 I cache: 16K, L1 D cache: 16K
> CPU: L2 cache: 128K
> Intel machine check reporting enabled on CPU#1.
> CPU: After vendor init, caps: 0183fbff 00000000 00000000 00000000
> CPU: After generic, caps: 0183fbff 00000000 00000000 00000000
> CPU: Common caps: 0183fbff 00000000 00000000 00000000
> CPU1: Intel Celeron (Mendocino) stepping 05
> Total of 2 processors activated (2202.00 BogoMIPS).
> ENABLING IO-APIC IRQs
> ...changing IO-APIC physical APIC ID to 2 ... ok.
> init IO_APIC IRQs
> IO-APIC (apicid-pin) 2-0, 2-10, 2-11, 2-12, 2-17, 2-20, 2-21, 2-22,
> 2-23 not connected.
> ..TIMER: vector=0x31 pin1=2 pin2=0
> number of MP IRQ sources: 16.
> number of IO-APIC #2 registers: 24.
> testing the IO APIC.......................
>
> IO APIC #2......
> .... register #00: 02000000
> ....... : physical APIC id: 02
> .... register #01: 00170011
> ....... : max redirection entries: 0017
> ....... : IO APIC version: 0011
> .... register #02: 00000000
> ....... : arbitration: 00
> .... IRQ redirection table:
> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
> 00 000 00 1 0 0 0 0 0 0 00
> 01 003 03 0 0 0 0 0 1 1 39
> 02 003 03 0 0 0 0 0 1 1 31
> 03 003 03 0 0 0 0 0 1 1 41
> 04 003 03 0 0 0 0 0 1 1 49
> 05 003 03 0 0 0 0 0 1 1 51
> 06 003 03 0 0 0 0 0 1 1 59
> 07 003 03 0 0 0 0 0 1 1 61
> 08 003 03 0 0 0 0 0 1 1 69
> 09 003 03 0 0 0 0 0 1 1 71
> 0a 000 00 1 0 0 0 0 0 0 00
> 0b 000 00 1 0 0 0 0 0 0 00
> 0c 000 00 1 0 0 0 0 0 0 00
> 0d 003 03 0 0 0 0 0 1 1 79
> 0e 003 03 0 0 0 0 0 1 1 81
> 0f 003 03 0 0 0 0 0 1 1 89
> 10 003 03 1 1 0 1 0 1 1 91
> 11 000 00 1 0 0 0 0 0 0 00
> 12 003 03 1 1 0 1 0 1 1 99
> 13 003 03 1 1 0 1 0 1 1 A1
> 14 000 00 1 0 0 0 0 0 0 00
> 15 000 00 1 0 0 0 0 0 0 00
> 16 000 00 1 0 0 0 0 0 0 00
> 17 000 00 1 0 0 0 0 0 0 00
> IRQ to pin mappings:
> IRQ0 -> 0:2
> IRQ1 -> 0:1
> IRQ3 -> 0:3
> IRQ4 -> 0:4
> IRQ5 -> 0:5
> IRQ6 -> 0:6
> IRQ7 -> 0:7
> IRQ8 -> 0:8
> IRQ9 -> 0:9
> IRQ10 -> 0:19
> IRQ11 -> 0:18
> IRQ12 -> 0:16
> IRQ13 -> 0:13
> IRQ14 -> 0:14
> IRQ15 -> 0:15
> .................................... done.
> Using local APIC timer interrupts.
> calibrating APIC timer ...
> ..... CPU clock speed is 551.2717 MHz.
> ..... host bus clock speed is 100.2310 MHz.
> cpu: 0, clocks: 1002310, slice: 334103
> CPU0<T0:1002304,T1:668192,D:9,S:334103,C:1002310>
> cpu: 1, clocks: 1002310, slice: 334103
> CPU1<T0:1002304,T1:334096,D:2,S:334103,C:1002310>
> checking TSC synchronization across CPUs: passed.
> mtrr: your CPUs had inconsistent fixed MTRR settings
> mtrr: probably your BIOS does not setup all CPUs
> PCI: PCI BIOS revision 2.10 entry at 0xfb5c0, last bus=1
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
> Limiting direct PCI/PCI transfers.
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
> apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
> apm: disabled - APM is not SMP safe.
> mxt_scan_bios: enter
> Starting kswapd v1.8
> VFS: Diskquotas version dquot_6.5.0 initialized
> Detected PS/2 Mouse Port.
> pty: 2048 Unix98 ptys configured
> Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT
> SHARE_IRQ SERIAL_PCI ISAPNP enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> Real Time Clock Driver v1.10d
> block: queued sectors max/low 338757kB/207685kB, 1024 slots per queue
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz PCI bus speed for PIO modes; override with idebus=xx
> PIIX4: IDE controller on PCI bus 00 dev 39
> PIIX4: chipset revision 1
> PIIX4: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
> ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
> HPT366: onboard version of chipset, pin1=1 pin2=2
> HPT366: IDE controller on PCI bus 00 dev 98
> HPT366: chipset revision 1
> HPT366: not 100% native mode: will probe irqs later
> ide2: BM-DMA at 0xe000-0xe007, BIOS settings: hde:pio, hdf:pio
> HPT366: IDE controller on PCI bus 00 dev 99
> HPT366: chipset revision 1
> HPT366: not 100% native mode: will probe irqs later
> ide3: BM-DMA at 0xec00-0xec07, BIOS settings: hdg:pio, hdh:pio
> hda: ST38410A, ATA DISK drive
> hdc: LTN382, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: 16841664 sectors (8623 MB) w/512KiB Cache, CHS=1048/255/63,
> UDMA(33)
> ide-floppy driver 0.97
> Partition check:
> hda: hda1 hda2 hda3 < hda5 hda6 >
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> ide-floppy driver 0.97
> md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> IP: routing cache hash table of 4096 buckets, 32Kbytes
> TCP: Hash tables configured (established 32768 bind 32768)
> Linux IP multicast router 0.06 plus PIM-SM
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> RAMDISK: Compressed image found at block 0
> Freeing initrd memory: 323k freed
> VFS: Mounted root (ext2 filesystem).
> Journalled Block Device driver loaded
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> Freeing unused kernel memory: 240k freed
> Adding Swap: 136512k swap-space (priority -1)
> Adding Swap: 519160k swap-space (priority -2)
> EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,2), internal journal
> kjournald starting. Commit interval 5 seconds
> EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,5), internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS 2.4-0.9.8, 25 Aug 2001 on ide0(3,6), internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> ip_tables: (c)2000 Netfilter core team
> ip_conntrack (4095 buckets, 32760 max)
> via-rhine.c:v1.10-LK1.1.10 07/12/2001 Written by Donald Becker
> http://www.scyld.com/network/via-rhine.html
> eth0: VIA VT3043 Rhine at 0xd400, 00:a0:0c:c0:0e:a2, IRQ 10.
> eth0: MII PHY found at address 1, status 0x782d advertising 05e1 Link
> 0000.
> wd.c: Presently autoprobing (not recommended) for a single card.
> wd.c:v1.10 9/23/94 Donald Becker (becker at cesdis.gsfc.nasa.gov)
> eth1: WD80x3 at 0x280, 00 00 C0 CC 27 1C WD8003, IRQ 3, shared memory
> at 0xd0000-0xd1fff.
> i2c-core.o: i2c core module
> piix4.o version 2.5.5 (20010115)
> i2c-core.o: adapter SMBus PIIX4 adapter at 5000 registered as adapter 0.
> i2c-piix4.o: PIIX4 bus detected and initialized
> sensors.o version 2.5.5 (20010115)
> w83781d.o version 2.5.5 (20010115)
> i2c-core.o: driver W83781D sensor driver registered.
> i2c-core.o: client [W83782D chip] registered to adapter [SMBus PIIX4
> adapter at 5000](pos. 0).
> i2c-core.o: client [W83782D subclient] registered to adapter [SMBus
> PIIX4 adapter at 5000](pos. 1).
> i2c-core.o: client [W83782D subclient] registered to adapter [SMBus
> PIIX4 adapter at 5000](pos. 2).
> parport0: PC-style at 0x378 [PCSPP,TRISTATE]
> parport0: cpp_daisy: aa5500ff(38)
> parport0: assign_addrs: aa5500ff(38)
> parport0: cpp_daisy: aa5500ff(38)
> parport0: assign_addrs: aa5500ff(38)
More information about the lm-sensors
mailing list