[lm-sensors] Ticket #2124, K8N-DL Readings

Ymu at Winbond.com.tw Ymu at Winbond.com.tw
Tue Dec 20 02:37:16 CET 2005

> The basic problem was with an Asus K8n-DL motherboard. Following
> suggestions, I have been able to get virtually all the problems ironed
> out, and although there is the w83627thf chip on the board, it does
> like this is useless, and only the w83792d is valid.
> There are just 2 values which are being reported incorrectly. Fan1 is
> reporting 11250RPM, however the bios is showing only 5554RPM. I have
> adjusting the div between 2, 4 and 8 however this has not changed the
> reading (the output from sensors does show the change in div value).
FAQ: 4.1 My fans report exactly half/double their values compared to the

> Also, comparing the voltage outputs from that of sensors, to those in
> bios, with the exception of VIN1, all the inputs appear correct, and
> match up. However the bios shows a reading of +12V, which is not shown
> sensors. The position within the bios screen is at the same place as
> (which reads +3.14V), and the +3.14V does not show anywhere within the
> bios - therefore I am assuming this should be +12V but being misread.
It seems that the sensors.conf is not correct for your board, but it's
hard to give a general sensors.conf for all boards using w83792d.
Best would if you can give a compute formula in sensors.conf by

Best Regards
Yuan Mu

===========================================================================================The privileged confidential information contained in this email is intended for use only by the addressees as indicated by the original sender of this email. If you are not the addressee indicated in this email or are not responsible for delivery of the email to such  a person, please kindly reply to the sender indicating this fact and delete all copies of it from your computer and network server immediately. Your cooperation is highly appreciated. It is advised that any unauthorized use of confidential information of Winbond is strictly prohibited; and any information in this email irrelevant to the official business of Winbond shall be deemed as neither given nor endorsed by Winbond.
===========================================================================================If your computer is unable to decode Chinese font, please ignore the following message.It essentially repeats the statement in English given above.¥»«H¥ó¤º©Ò§tµØ¨¹¹q¤lªº°]²£©Ê¾÷±K©Ê¸ê°T, ¶È±ÂÅv­ìµo«H¤H«ü©w¤§¦¬«H¤H¨ú¾\\¤§¥Î. °²¨Ï±z¨Ã«D³Q«ü©w¤§¦¬«H¤H©Î¦]¥ô¦ó­ì¦]¦b¥¼¸g±ÂÅvªº±¡§Î¤§¤U¦¬¨ì¥»«H¥ó, ½Ð±z§iª¾­ìµo«H¤H¨Ã¥ß§Y±N«H¥ó±q¹q¸£»Pºô¸ô¦øªA¾¹¤¤¤©¥H®ø°£. ¹ï©ó±zªº¦X§@, §Ú­Ì¥ý¦¹­PÁÂ. ¯S¦¹´£¿ô, ¥ô¦ó¥¼¸g±ÂÅv¾Õ¦Û¨Ï¥ÎµØ¨¹¹q¤lªº¾÷±K¸ê°Tªº¦æ¬°¬O³QÄY®æ¸T¤îªº. «H¥ó»PµØ¨¹¹q¤lÀç·~µLÃö¤§¤º®e,¤£±oµø¬°µØ¨¹¹q¤l¤§¥ß³õ©Î·N¨£.

More information about the lm-sensors mailing list