[lm-sensors] patch hwmon-vt1211-new-driver.patch added to gregkh-2.6 tree

gregkh at suse.de gregkh at suse.de
Thu Sep 28 09:01:54 CEST 2006


This is a note to let you know that I've just added the patch titled

     Subject: [PATCH 05/23] hwmon: New driver for the VIA VT1211

to my gregkh-2.6 tree.  Its filename is

     hwmon-vt1211-new-driver.patch

This tree can be found at 
    http://www.kernel.org/pub/linux/kernel/people/gregkh/gregkh-2.6/patches/


>From khali at linux-fr.org Sun Sep 24 11:54:10 2006
Date: Sun, 24 Sep 2006 20:54:04 +0200
From: Jean Delvare <khali at linux-fr.org>
To: Greg KH <greg at kroah.com>
Cc: LM Sensors <lm-sensors at lm-sensors.org>, Juerg Haefliger <juergh at gmail.com>
Subject: [PATCH 05/23] hwmon: New driver for the VIA VT1211
Message-Id: <20060924205404.062292da.khali at linux-fr.org>
Content-Disposition: inline; filename=hwmon-vt1211-new-driver.patch

From: Juerg Haefliger <juergh at gmail.com>

hwmon: New driver for the VIA VT1211

This is a new driver for the VIA VT1211 Super-IO chip. It is a rewrite
of the existing vt1211 driver (by Mark D. Studebaker and Lars Ekman)
which has been around for a while but never made it into the main
kernel tree.

It is implemented as a platform driver and therefore requires
lm_sensors 2.10.1 to function properly.

Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Jean Delvare <khali at linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh at suse.de>

---
 MAINTAINERS            |    6 
 drivers/hwmon/Kconfig  |   11 
 drivers/hwmon/Makefile |    1 
 drivers/hwmon/vt1211.c | 1355 +++++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 1373 insertions(+)

--- gregkh-2.6.orig/MAINTAINERS
+++ gregkh-2.6/MAINTAINERS
@@ -3310,6 +3310,12 @@ W:	http://linuxtv.org
 T:	git kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb.git
 S:	Maintained
 
+VT1211 HARDWARE MONITOR DRIVER
+P:	Juerg Haefliger
+M:	juergh at gmail.com
+L:	lm-sensors at lm-sensors.org
+S:	Maintained
+
 VT8231 HARDWARE MONITOR DRIVER
 P:	Roger Lucas
 M:	roger at planbit.co.uk
--- gregkh-2.6.orig/drivers/hwmon/Kconfig
+++ gregkh-2.6/drivers/hwmon/Kconfig
@@ -417,6 +417,17 @@ config SENSORS_VIA686A
 	  This driver can also be built as a module.  If so, the module
 	  will be called via686a.
 
+config SENSORS_VT1211
+	tristate "VIA VT1211"
+	depends on HWMON && EXPERIMENTAL
+	select HWMON_VID
+	help
+	  If you say yes here then you get support for hardware monitoring
+	  features of the VIA VT1211 Super-I/O chip.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called vt1211.
+
 config SENSORS_VT8231
 	tristate "VIA VT8231"
 	depends on HWMON && I2C && PCI && EXPERIMENTAL
--- gregkh-2.6.orig/drivers/hwmon/Makefile
+++ gregkh-2.6/drivers/hwmon/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc4
 obj-$(CONFIG_SENSORS_SMSC47M1)	+= smsc47m1.o
 obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
 obj-$(CONFIG_SENSORS_VIA686A)	+= via686a.o
+obj-$(CONFIG_SENSORS_VT1211)	+= vt1211.o
 obj-$(CONFIG_SENSORS_VT8231)	+= vt8231.o
 obj-$(CONFIG_SENSORS_W83627EHF)	+= w83627ehf.o
 obj-$(CONFIG_SENSORS_W83L785TS)	+= w83l785ts.o
--- /dev/null
+++ gregkh-2.6/drivers/hwmon/vt1211.c
@@ -0,0 +1,1355 @@
+/*
+ * vt1211.c - driver for the VIA VT1211 Super-I/O chip integrated hardware
+ *            monitoring features
+ * Copyright (C) 2006 Juerg Haefliger <juergh at gmail.com>
+ *
+ * This driver is based on the driver for kernel 2.4 by Mark D. Studebaker
+ * and its port to kernel 2.6 by Lars Ekman.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/platform_device.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/hwmon-vid.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <asm/io.h>
+
+static int uch_config = -1;
+module_param(uch_config, int, 0);
+MODULE_PARM_DESC(uch_config, "Initialize the universal channel configuration");
+
+static int int_mode = -1;
+module_param(int_mode, int, 0);
+MODULE_PARM_DESC(int_mode, "Force the temperature interrupt mode");
+
+static struct platform_device *pdev;
+
+#define DRVNAME "vt1211"
+
+/* ---------------------------------------------------------------------
+ * Registers
+ *
+ * The sensors are defined as follows.
+ *
+ * Sensor          Voltage Mode   Temp Mode   Notes (from the datasheet)
+ * --------        ------------   ---------   --------------------------
+ * Reading 1                      temp1       Intel thermal diode
+ * Reading 3                      temp2       Internal thermal diode
+ * UCH1/Reading2   in0            temp3       NTC type thermistor
+ * UCH2            in1            temp4       +2.5V
+ * UCH3            in2            temp5       VccP
+ * UCH4            in3            temp6       +5V
+ * UCH5            in4            temp7       +12V
+ * 3.3V            in5                        Internal VDD (+3.3V)
+ *
+ * --------------------------------------------------------------------- */
+
+/* Voltages (in) numbered 0-5 (ix) */
+#define VT1211_REG_IN(ix)		(0x21 + (ix))
+#define VT1211_REG_IN_MIN(ix)		((ix) == 0 ? 0x3e : 0x2a + 2 * (ix))
+#define VT1211_REG_IN_MAX(ix)		((ix) == 0 ? 0x3d : 0x29 + 2 * (ix))
+
+/* Temperatures (temp) numbered 0-6 (ix) */
+static u8 regtemp[]	= {0x1f, 0x20, 0x21, 0x22, 0x23, 0x24, 0x25};
+static u8 regtempmax[]	= {0x39, 0x1d, 0x3d, 0x2b, 0x2d, 0x2f, 0x31};
+static u8 regtemphyst[]	= {0x3a, 0x1e, 0x3e, 0x2c, 0x2e, 0x30, 0x32};
+
+/* Fans numbered 0-1 (ix) */
+#define VT1211_REG_FAN(ix)		(0x29 + (ix))
+#define VT1211_REG_FAN_MIN(ix)		(0x3b + (ix))
+#define VT1211_REG_FAN_DIV		 0x47
+
+/* PWMs numbered 0-1 (ix) */
+/* Auto points numbered 0-3 (ap) */
+#define VT1211_REG_PWM(ix)		(0x60 + (ix))
+#define VT1211_REG_PWM_CLK		 0x50
+#define VT1211_REG_PWM_CTL		 0x51
+#define VT1211_REG_PWM_AUTO_TEMP(ap)	(0x55 - (ap))
+#define VT1211_REG_PWM_AUTO_PWM(ix, ap)	(0x58 + 2 * (ix) - (ap))
+
+/* Miscellaneous registers */
+#define VT1211_REG_CONFIG		0x40
+#define VT1211_REG_ALARM1		0x41
+#define VT1211_REG_ALARM2		0x42
+#define VT1211_REG_VID			0x45
+#define VT1211_REG_UCH_CONFIG		0x4a
+#define VT1211_REG_TEMP1_CONFIG		0x4b
+#define VT1211_REG_TEMP2_CONFIG		0x4c
+
+/* In, temp & fan alarm bits */
+static const u8 bitalarmin[]	= {11, 0, 1, 3, 8, 2, 9};
+static const u8 bitalarmtemp[]	= {4, 15, 11, 0, 1, 3, 8};
+static const u8 bitalarmfan[]	= {6, 7};
+
+/* ---------------------------------------------------------------------
+ * Data structures and manipulation thereof
+ * --------------------------------------------------------------------- */
+
+struct vt1211_data {
+	unsigned short addr;
+	const char *name;
+	struct class_device *class_dev;
+
+	struct mutex update_lock;
+	char valid;			/* !=0 if following fields are valid */
+	unsigned long last_updated;	/* In jiffies */
+
+	/* Register values */
+	u8  in[6];
+	u8  in_max[6];
+	u8  in_min[6];
+	u8  temp[7];
+	u8  temp_max[7];
+	u8  temp_hyst[7];
+	u8  fan[2];
+	u8  fan_min[2];
+	u8  fan_div[2];
+	u8  fan_ctl;
+	u8  pwm[2];
+	u8  pwm_ctl[2];
+	u8  pwm_clk;
+	u8  pwm_auto_temp[4];
+	u8  pwm_auto_pwm[2][4];
+	u8  vid;		/* Read once at init time */
+	u8  vrm;
+	u8  uch_config;		/* Read once at init time */
+	u16 alarms;
+};
+
+/* ix = [0-5] */
+#define ISVOLT(ix, uch_config)	((ix) > 4 ? 1 : \
+				 !(((uch_config) >> ((ix) + 2)) & 1))
+
+/* ix = [0-6] */
+#define ISTEMP(ix, uch_config)	((ix) < 2 ? 1 : \
+				 ((uch_config) >> (ix)) & 1)
+
+/* in5 (ix = 5) is special. It's the internal 3.3V so it's scaled in the
+   driver according to the VT1211 BIOS porting guide */
+#define IN_FROM_REG(ix, reg)	((reg) < 3 ? 0 : (ix) == 5 ? \
+				 (((reg) - 3) * 15882 + 479) / 958 : \
+				 (((reg) - 3) * 10000 + 479) / 958)
+#define IN_TO_REG(ix, val)	(SENSORS_LIMIT((ix) == 5 ? \
+				 ((val) * 958 + 7941) / 15882 + 3 : \
+				 ((val) * 958 + 5000) / 10000 + 3, 0, 255))
+
+/* temp1 (ix = 0) is an intel thermal diode which is scaled in user space.
+   temp2 (ix = 1) is the internal temp diode so it's scaled in the driver
+   according to some measurements that I took on an EPIA M10000.
+   temp3-7 are thermistor based so the driver returns the voltage measured at
+   the pin (range 0V - 2.2V). */
+#define TEMP_FROM_REG(ix, reg)	((ix) == 0 ? (reg) * 1000 : \
+				 (ix) == 1 ? (reg) < 51 ? 0 : \
+				 ((reg) - 51) * 1000 : \
+				 ((253 - (reg)) * 2200 + 105) / 210)
+#define TEMP_TO_REG(ix, val)	SENSORS_LIMIT( \
+				 ((ix) == 0 ? ((val) + 500) / 1000 : \
+				  (ix) == 1 ? ((val) + 500) / 1000 + 51 : \
+				  253 - ((val) * 210 + 1100) / 2200), 0, 255)
+
+#define DIV_FROM_REG(reg)	(1 << (reg))
+
+#define RPM_FROM_REG(reg, div)	(((reg) == 0) || ((reg) == 255) ? 0 : \
+				 1310720 / (reg) / DIV_FROM_REG(div))
+#define RPM_TO_REG(val, div)	((val) == 0 ? 255 : \
+				 SENSORS_LIMIT((1310720 / (val) / \
+				 DIV_FROM_REG(div)), 1, 254))
+
+/* ---------------------------------------------------------------------
+ * Super-I/O constants and functions
+ * --------------------------------------------------------------------- */
+
+/* Configuration & data index port registers */
+#define SIO_REG_CIP		0x2e
+#define SIO_REG_DIP		0x2f
+
+/* Configuration registers */
+#define SIO_VT1211_LDN		0x07	/* logical device number */
+#define SIO_VT1211_DEVID	0x20	/* device ID */
+#define SIO_VT1211_DEVREV	0x21	/* device revision */
+#define SIO_VT1211_ACTIVE	0x30	/* HW monitor active */
+#define SIO_VT1211_BADDR	0x60	/* base I/O address */
+#define SIO_VT1211_ID		0x3c	/* VT1211 device ID */
+
+/* VT1211 logical device numbers */
+#define SIO_VT1211_LDN_HWMON	0x0b	/* HW monitor */
+
+static inline void superio_outb(int reg, int val)
+{
+	outb(reg, SIO_REG_CIP);
+	outb(val, SIO_REG_DIP);
+}
+
+static inline int superio_inb(int reg)
+{
+	outb(reg, SIO_REG_CIP);
+	return inb(SIO_REG_DIP);
+}
+
+static inline void superio_select(int ldn)
+{
+	outb(SIO_VT1211_LDN, SIO_REG_CIP);
+	outb(ldn, SIO_REG_DIP);
+}
+
+static inline void superio_enter(void)
+{
+	outb(0x87, SIO_REG_CIP);
+	outb(0x87, SIO_REG_CIP);
+}
+
+static inline void superio_exit(void)
+{
+	outb(0xaa, SIO_REG_CIP);
+}
+
+/* ---------------------------------------------------------------------
+ * Device I/O access
+ * --------------------------------------------------------------------- */
+
+static inline u8 vt1211_read8(struct vt1211_data *data, u8 reg)
+{
+	return inb(data->addr + reg);
+}
+
+static inline void vt1211_write8(struct vt1211_data *data, u8 reg, u8 val)
+{
+	outb(val, data->addr + reg);
+}
+
+static struct vt1211_data *vt1211_update_device(struct device *dev)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+	int ix, val;
+
+	mutex_lock(&data->update_lock);
+
+	/* registers cache is refreshed after 1 second */
+	if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
+		/* read VID */
+		data->vid = vt1211_read8(data, VT1211_REG_VID) & 0x1f;
+
+		/* voltage (in) registers */
+		for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) {
+			if (ISVOLT(ix, data->uch_config)) {
+				data->in[ix] = vt1211_read8(data,
+						VT1211_REG_IN(ix));
+				data->in_min[ix] = vt1211_read8(data,
+						VT1211_REG_IN_MIN(ix));
+				data->in_max[ix] = vt1211_read8(data,
+						VT1211_REG_IN_MAX(ix));
+			}
+		}
+
+		/* temp registers */
+		for (ix = 0; ix < ARRAY_SIZE(data->temp); ix++) {
+			if (ISTEMP(ix, data->uch_config)) {
+				data->temp[ix] = vt1211_read8(data,
+						regtemp[ix]);
+				data->temp_max[ix] = vt1211_read8(data,
+						regtempmax[ix]);
+				data->temp_hyst[ix] = vt1211_read8(data,
+						regtemphyst[ix]);
+			}
+		}
+
+		/* fan & pwm registers */
+		for (ix = 0; ix < ARRAY_SIZE(data->fan); ix++) {
+			data->fan[ix] = vt1211_read8(data,
+						VT1211_REG_FAN(ix));
+			data->fan_min[ix] = vt1211_read8(data,
+						VT1211_REG_FAN_MIN(ix));
+			data->pwm[ix] = vt1211_read8(data,
+						VT1211_REG_PWM(ix));
+		}
+		val = vt1211_read8(data, VT1211_REG_FAN_DIV);
+		data->fan_div[0] = (val >> 4) & 3;
+		data->fan_div[1] = (val >> 6) & 3;
+		data->fan_ctl = val & 0xf;
+
+		val = vt1211_read8(data, VT1211_REG_PWM_CTL);
+		data->pwm_ctl[0] = val & 0xf;
+		data->pwm_ctl[1] = (val >> 4) & 0xf;
+
+		data->pwm_clk = vt1211_read8(data, VT1211_REG_PWM_CLK);
+
+		/* pwm & temp auto point registers */
+		data->pwm_auto_pwm[0][1] = vt1211_read8(data,
+						VT1211_REG_PWM_AUTO_PWM(0, 1));
+		data->pwm_auto_pwm[0][2] = vt1211_read8(data,
+						VT1211_REG_PWM_AUTO_PWM(0, 2));
+		data->pwm_auto_pwm[1][1] = vt1211_read8(data,
+						VT1211_REG_PWM_AUTO_PWM(1, 1));
+		data->pwm_auto_pwm[1][2] = vt1211_read8(data,
+						VT1211_REG_PWM_AUTO_PWM(1, 2));
+		for (ix = 0; ix < ARRAY_SIZE(data->pwm_auto_temp); ix++) {
+			data->pwm_auto_temp[ix] = vt1211_read8(data,
+						VT1211_REG_PWM_AUTO_TEMP(ix));
+		}
+
+		/* alarm registers */
+		data->alarms = (vt1211_read8(data, VT1211_REG_ALARM2) << 8) |
+				vt1211_read8(data, VT1211_REG_ALARM1);
+
+		data->last_updated = jiffies;
+		data->valid = 1;
+	}
+
+	mutex_unlock(&data->update_lock);
+
+	return data;
+}
+
+/* ---------------------------------------------------------------------
+ * Voltage sysfs interfaces
+ * ix = [0-5]
+ * --------------------------------------------------------------------- */
+
+#define SHOW_IN_INPUT	0
+#define SHOW_SET_IN_MIN	1
+#define SHOW_SET_IN_MAX	2
+#define SHOW_IN_ALARM	3
+
+static ssize_t show_in(struct device *dev, struct device_attribute *attr,
+		       char *buf)
+{
+	struct vt1211_data *data = vt1211_update_device(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	int res;
+
+	switch (fn) {
+	case SHOW_IN_INPUT:
+		res = IN_FROM_REG(ix, data->in[ix]);
+		break;
+	case SHOW_SET_IN_MIN:
+		res = IN_FROM_REG(ix, data->in_min[ix]);
+		break;
+	case SHOW_SET_IN_MAX:
+		res = IN_FROM_REG(ix, data->in_max[ix]);
+		break;
+	case SHOW_IN_ALARM:
+		res = (data->alarms >> bitalarmin[ix]) & 1;
+		break;
+	default:
+		res = 0;
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+	return sprintf(buf, "%d\n", res);
+}
+
+static ssize_t set_in(struct device *dev, struct device_attribute *attr,
+		      const char *buf, size_t count)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	switch (fn) {
+	case SHOW_SET_IN_MIN:
+		data->in_min[ix] = IN_TO_REG(ix, val);
+		vt1211_write8(data, VT1211_REG_IN_MIN(ix), data->in_min[ix]);
+		break;
+	case SHOW_SET_IN_MAX:
+		data->in_max[ix] = IN_TO_REG(ix, val);
+		vt1211_write8(data, VT1211_REG_IN_MAX(ix), data->in_max[ix]);
+		break;
+	default:
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+/* ---------------------------------------------------------------------
+ * Temperature sysfs interfaces
+ * ix = [0-6]
+ * --------------------------------------------------------------------- */
+
+#define SHOW_TEMP_INPUT		0
+#define SHOW_SET_TEMP_MAX	1
+#define SHOW_SET_TEMP_MAX_HYST	2
+#define SHOW_TEMP_ALARM		3
+
+static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
+			 char *buf)
+{
+	struct vt1211_data *data = vt1211_update_device(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	int res;
+
+	switch (fn) {
+	case SHOW_TEMP_INPUT:
+		res = TEMP_FROM_REG(ix, data->temp[ix]);
+		break;
+	case SHOW_SET_TEMP_MAX:
+		res = TEMP_FROM_REG(ix, data->temp_max[ix]);
+		break;
+	case SHOW_SET_TEMP_MAX_HYST:
+		res = TEMP_FROM_REG(ix, data->temp_hyst[ix]);
+		break;
+	case SHOW_TEMP_ALARM:
+		res = (data->alarms >> bitalarmtemp[ix]) & 1;
+		break;
+	default:
+		res = 0;
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+	return sprintf(buf, "%d\n", res);
+}
+
+static ssize_t set_temp(struct device *dev, struct device_attribute *attr,
+			const char *buf, size_t count)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+
+	mutex_lock(&data->update_lock);
+	switch (fn) {
+	case SHOW_SET_TEMP_MAX:
+		data->temp_max[ix] = TEMP_TO_REG(ix, val);
+		vt1211_write8(data, regtempmax[ix],
+			      data->temp_max[ix]);
+		break;
+	case SHOW_SET_TEMP_MAX_HYST:
+		data->temp_hyst[ix] = TEMP_TO_REG(ix, val);
+		vt1211_write8(data, regtemphyst[ix],
+			      data->temp_hyst[ix]);
+		break;
+	default:
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+/* ---------------------------------------------------------------------
+ * Fan sysfs interfaces
+ * ix = [0-1]
+ * --------------------------------------------------------------------- */
+
+#define SHOW_FAN_INPUT		0
+#define SHOW_SET_FAN_MIN	1
+#define SHOW_SET_FAN_DIV	2
+#define SHOW_FAN_ALARM		3
+
+static ssize_t show_fan(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct vt1211_data *data = vt1211_update_device(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	int res;
+
+	switch (fn) {
+	case SHOW_FAN_INPUT:
+		res = RPM_FROM_REG(data->fan[ix], data->fan_div[ix]);
+		break;
+	case SHOW_SET_FAN_MIN:
+		res = RPM_FROM_REG(data->fan_min[ix], data->fan_div[ix]);
+		break;
+	case SHOW_SET_FAN_DIV:
+		res = DIV_FROM_REG(data->fan_div[ix]);
+		break;
+	case SHOW_FAN_ALARM:
+		res = (data->alarms >> bitalarmfan[ix]) & 1;
+		break;
+	default:
+		res = 0;
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+	return sprintf(buf, "%d\n", res);
+}
+
+static ssize_t set_fan(struct device *dev, struct device_attribute *attr,
+		       const char *buf, size_t count)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+	int reg;
+
+	mutex_lock(&data->update_lock);
+
+	/* sync the data cache */
+	reg = vt1211_read8(data, VT1211_REG_FAN_DIV);
+	data->fan_div[0] = (reg >> 4) & 3;
+	data->fan_div[1] = (reg >> 6) & 3;
+	data->fan_ctl = reg & 0xf;
+
+	switch (fn) {
+	case SHOW_SET_FAN_MIN:
+		data->fan_min[ix] = RPM_TO_REG(val, data->fan_div[ix]);
+		vt1211_write8(data, VT1211_REG_FAN_MIN(ix),
+			      data->fan_min[ix]);
+		break;
+	case SHOW_SET_FAN_DIV:
+		switch (val) {
+			case 1: data->fan_div[ix] = 0; break;
+			case 2: data->fan_div[ix] = 1; break;
+			case 4: data->fan_div[ix] = 2; break;
+			case 8: data->fan_div[ix] = 3; break;
+			default:
+				count = -EINVAL;
+				dev_warn(dev, "fan div value %ld not "
+					 "supported. Choose one of 1, 2, "
+					 "4, or 8.\n", val);
+				goto EXIT;
+		}
+		vt1211_write8(data, VT1211_REG_FAN_DIV,
+			      ((data->fan_div[1] << 6) |
+			       (data->fan_div[0] << 4) |
+				data->fan_ctl));
+		break;
+	default:
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+EXIT:
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+/* ---------------------------------------------------------------------
+ * PWM sysfs interfaces
+ * ix = [0-1]
+ * --------------------------------------------------------------------- */
+
+#define SHOW_PWM			0
+#define SHOW_SET_PWM_ENABLE		1
+#define SHOW_SET_PWM_FREQ		2
+#define SHOW_SET_PWM_AUTO_CHANNELS_TEMP	3
+
+static ssize_t show_pwm(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct vt1211_data *data = vt1211_update_device(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	int res;
+
+	switch (fn) {
+	case SHOW_PWM:
+		res = data->pwm[ix];
+		break;
+	case SHOW_SET_PWM_ENABLE:
+		res = ((data->pwm_ctl[ix] >> 3) & 1) ? 2 : 0;
+		break;
+	case SHOW_SET_PWM_FREQ:
+		res = 90000 >> (data->pwm_clk & 7);
+		break;
+	case SHOW_SET_PWM_AUTO_CHANNELS_TEMP:
+		res = (data->pwm_ctl[ix] & 7) + 1;
+		break;
+	default:
+		res = 0;
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+	return sprintf(buf, "%d\n", res);
+}
+
+static ssize_t set_pwm(struct device *dev, struct device_attribute *attr,
+		       const char *buf, size_t count)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int fn = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+	int tmp, reg;
+
+	mutex_lock(&data->update_lock);
+
+	switch (fn) {
+	case SHOW_SET_PWM_ENABLE:
+		/* sync the data cache */
+		reg = vt1211_read8(data, VT1211_REG_FAN_DIV);
+		data->fan_div[0] = (reg >> 4) & 3;
+		data->fan_div[1] = (reg >> 6) & 3;
+		data->fan_ctl = reg & 0xf;
+		reg = vt1211_read8(data, VT1211_REG_PWM_CTL);
+		data->pwm_ctl[0] = reg & 0xf;
+		data->pwm_ctl[1] = (reg >> 4) & 0xf;
+		switch (val) {
+		case 0:
+			data->pwm_ctl[ix] &= 7;
+			/* disable SmartGuardian if both PWM outputs are
+			 * disabled */
+			if ((data->pwm_ctl[ix ^ 1] & 1) == 0) {
+				data->fan_ctl &= 0xe;
+			}
+			break;
+		case 2:
+			data->pwm_ctl[ix] |= 8;
+			data->fan_ctl |= 1;
+			break;
+		default:
+			count = -EINVAL;
+			dev_warn(dev, "pwm mode %ld not supported. "
+				 "Choose one of 0 or 2.\n", val);
+			goto EXIT;
+		}
+		vt1211_write8(data, VT1211_REG_PWM_CTL,
+			      ((data->pwm_ctl[1] << 4) |
+				data->pwm_ctl[0]));
+		vt1211_write8(data, VT1211_REG_FAN_DIV,
+			      ((data->fan_div[1] << 6) |
+			       (data->fan_div[0] << 4) |
+				data->fan_ctl));
+		break;
+	case SHOW_SET_PWM_FREQ:
+		val = 135000 / SENSORS_LIMIT(val, 135000 >> 7, 135000);
+		/* calculate tmp = log2(val) */
+		tmp = 0;
+		for (val >>= 1; val > 0; val >>= 1) {
+			tmp++;
+		}
+		/* sync the data cache */
+		reg = vt1211_read8(data, VT1211_REG_PWM_CLK);
+		data->pwm_clk = (reg & 0xf8) | tmp;
+		vt1211_write8(data, VT1211_REG_PWM_CLK, data->pwm_clk);
+		break;
+	case SHOW_SET_PWM_AUTO_CHANNELS_TEMP:
+		if ((val < 1) || (val > 7)) {
+			count = -EINVAL;
+			dev_warn(dev, "temp channel %ld not supported. "
+				 "Choose a value between 1 and 7.\n", val);
+			goto EXIT;
+		}
+		if (!ISTEMP(val - 1, data->uch_config)) {
+			count = -EINVAL;
+			dev_warn(dev, "temp channel %ld is not available.\n",
+				 val);
+			goto EXIT;
+		}
+		/* sync the data cache */
+		reg = vt1211_read8(data, VT1211_REG_PWM_CTL);
+		data->pwm_ctl[0] = reg & 0xf;
+		data->pwm_ctl[1] = (reg >> 4) & 0xf;
+		data->pwm_ctl[ix] = (data->pwm_ctl[ix] & 8) | (val - 1);
+		vt1211_write8(data, VT1211_REG_PWM_CTL,
+			      ((data->pwm_ctl[1] << 4) | data->pwm_ctl[0]));
+		break;
+	default:
+		dev_dbg(dev, "Unknown attr fetch (%d)\n", fn);
+	}
+
+EXIT:
+	mutex_unlock(&data->update_lock);
+	return count;
+}
+
+/* ---------------------------------------------------------------------
+ * PWM auto point definitions
+ * ix = [0-1]
+ * ap = [0-3]
+ * --------------------------------------------------------------------- */
+
+/*
+ * pwm[ix+1]_auto_point[ap+1]_temp mapping table:
+ * Note that there is only a single set of temp auto points that controls both
+ * PWM controllers. We still create 2 sets of sysfs files to make it look
+ * more consistent even though they map to the same registers.
+ *
+ * ix ap : description
+ * -------------------
+ * 0  0  : pwm1/2 off temperature        (pwm_auto_temp[0])
+ * 0  1  : pwm1/2 low speed temperature  (pwm_auto_temp[1])
+ * 0  2  : pwm1/2 high speed temperature (pwm_auto_temp[2])
+ * 0  3  : pwm1/2 full speed temperature (pwm_auto_temp[3])
+ * 1  0  : pwm1/2 off temperature        (pwm_auto_temp[0])
+ * 1  1  : pwm1/2 low speed temperature  (pwm_auto_temp[1])
+ * 1  2  : pwm1/2 high speed temperature (pwm_auto_temp[2])
+ * 1  3  : pwm1/2 full speed temperature (pwm_auto_temp[3])
+ */
+
+static ssize_t show_pwm_auto_point_temp(struct device *dev,
+					struct device_attribute *attr,
+					char *buf)
+{
+	struct vt1211_data *data = vt1211_update_device(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int ap = sensor_attr_2->nr;
+
+	return sprintf(buf, "%d\n", TEMP_FROM_REG(data->pwm_ctl[ix] & 7,
+		       data->pwm_auto_temp[ap]));
+}
+
+static ssize_t set_pwm_auto_point_temp(struct device *dev,
+				       struct device_attribute *attr,
+				       const char *buf, size_t count)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int ap = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+	int reg;
+
+	mutex_lock(&data->update_lock);
+
+	/* sync the data cache */
+	reg = vt1211_read8(data, VT1211_REG_PWM_CTL);
+	data->pwm_ctl[0] = reg & 0xf;
+	data->pwm_ctl[1] = (reg >> 4) & 0xf;
+
+	data->pwm_auto_temp[ap] = TEMP_TO_REG(data->pwm_ctl[ix] & 7, val);
+	vt1211_write8(data, VT1211_REG_PWM_AUTO_TEMP(ap),
+		      data->pwm_auto_temp[ap]);
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+/*
+ * pwm[ix+1]_auto_point[ap+1]_pwm mapping table:
+ * Note that the PWM auto points 0 & 3 are hard-wired in the VT1211 and can't
+ * be changed.
+ *
+ * ix ap : description
+ * -------------------
+ * 0  0  : pwm1 off                   (pwm_auto_pwm[0][0], hard-wired to 0)
+ * 0  1  : pwm1 low speed duty cycle  (pwm_auto_pwm[0][1])
+ * 0  2  : pwm1 high speed duty cycle (pwm_auto_pwm[0][2])
+ * 0  3  : pwm1 full speed            (pwm_auto_pwm[0][3], hard-wired to 255)
+ * 1  0  : pwm2 off                   (pwm_auto_pwm[1][0], hard-wired to 0)
+ * 1  1  : pwm2 low speed duty cycle  (pwm_auto_pwm[1][1])
+ * 1  2  : pwm2 high speed duty cycle (pwm_auto_pwm[1][2])
+ * 1  3  : pwm2 full speed            (pwm_auto_pwm[1][3], hard-wired to 255)
+*/
+
+static ssize_t show_pwm_auto_point_pwm(struct device *dev,
+				       struct device_attribute *attr,
+				       char *buf)
+{
+	struct vt1211_data *data = vt1211_update_device(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int ap = sensor_attr_2->nr;
+
+	return sprintf(buf, "%d\n", data->pwm_auto_pwm[ix][ap]);
+}
+
+static ssize_t set_pwm_auto_point_pwm(struct device *dev,
+				      struct device_attribute *attr,
+				      const char *buf, size_t count)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+	struct sensor_device_attribute_2 *sensor_attr_2 =
+						to_sensor_dev_attr_2(attr);
+	int ix = sensor_attr_2->index;
+	int ap = sensor_attr_2->nr;
+	long val = simple_strtol(buf, NULL, 10);
+
+	if ((val < 0) || (val > 255)) {
+		dev_err(dev, "pwm value %ld is out of range. "
+			"Choose a value between 0 and 255." , val);
+		return -EINVAL;
+	}
+
+	mutex_lock(&data->update_lock);
+	data->pwm_auto_pwm[ix][ap] = val;
+	vt1211_write8(data, VT1211_REG_PWM_AUTO_PWM(ix, ap),
+		      data->pwm_auto_pwm[ix][ap]);
+	mutex_unlock(&data->update_lock);
+
+	return count;
+}
+
+/* ---------------------------------------------------------------------
+ * Miscellaneous sysfs interfaces (VRM, VID, name, and (legacy) alarms)
+ * --------------------------------------------------------------------- */
+
+static ssize_t show_vrm(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+
+	return sprintf(buf, "%d\n", data->vrm);
+}
+
+static ssize_t set_vrm(struct device *dev, struct device_attribute *attr,
+		       const char *buf, size_t count)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+	long val = simple_strtol(buf, NULL, 10);
+
+	data->vrm = val;
+
+	return count;
+}
+
+static ssize_t show_vid(struct device *dev, struct device_attribute *attr,
+			char *buf)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+
+	return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm));
+}
+
+static ssize_t show_name(struct device *dev,
+			 struct device_attribute *attr, char *buf)
+{
+	struct vt1211_data *data = dev_get_drvdata(dev);
+
+	return sprintf(buf, "%s\n", data->name);
+}
+
+static ssize_t show_alarms(struct device *dev,
+			   struct device_attribute *attr, char *buf)
+{
+	struct vt1211_data *data = vt1211_update_device(dev);
+
+	return sprintf(buf, "%d\n", data->alarms);
+}
+
+/* ---------------------------------------------------------------------
+ * Device attribute structs
+ * --------------------------------------------------------------------- */
+
+#define SENSOR_ATTR_IN_INPUT(ix) \
+	SENSOR_ATTR_2(in##ix##_input, S_IRUGO, \
+		show_in, NULL, SHOW_IN_INPUT, ix)
+
+static struct sensor_device_attribute_2 vt1211_sysfs_in_input[] = {
+	SENSOR_ATTR_IN_INPUT(0),
+	SENSOR_ATTR_IN_INPUT(1),
+	SENSOR_ATTR_IN_INPUT(2),
+	SENSOR_ATTR_IN_INPUT(3),
+	SENSOR_ATTR_IN_INPUT(4),
+	SENSOR_ATTR_IN_INPUT(5),
+};
+
+#define SENSOR_ATTR_IN_MIN(ix) \
+	SENSOR_ATTR_2(in##ix##_min, S_IRUGO | S_IWUSR, \
+		show_in, set_in, SHOW_SET_IN_MIN, ix)
+
+static struct sensor_device_attribute_2 vt1211_sysfs_in_min[] = {
+	SENSOR_ATTR_IN_MIN(0),
+	SENSOR_ATTR_IN_MIN(1),
+	SENSOR_ATTR_IN_MIN(2),
+	SENSOR_ATTR_IN_MIN(3),
+	SENSOR_ATTR_IN_MIN(4),
+	SENSOR_ATTR_IN_MIN(5),
+};
+
+#define SENSOR_ATTR_IN_MAX(ix) \
+	SENSOR_ATTR_2(in##ix##_max, S_IRUGO | S_IWUSR, \
+		show_in, set_in, SHOW_SET_IN_MAX, ix)
+
+static struct sensor_device_attribute_2 vt1211_sysfs_in_max[] = {
+	SENSOR_ATTR_IN_MAX(0),
+	SENSOR_ATTR_IN_MAX(1),
+	SENSOR_ATTR_IN_MAX(2),
+	SENSOR_ATTR_IN_MAX(3),
+	SENSOR_ATTR_IN_MAX(4),
+	SENSOR_ATTR_IN_MAX(5),
+};
+
+#define SENSOR_ATTR_IN_ALARM(ix) \
+	SENSOR_ATTR_2(in##ix##_alarm, S_IRUGO, \
+		show_in, NULL, SHOW_IN_ALARM, ix)
+
+static struct sensor_device_attribute_2 vt1211_sysfs_in_alarm[] = {
+	SENSOR_ATTR_IN_ALARM(0),
+	SENSOR_ATTR_IN_ALARM(1),
+	SENSOR_ATTR_IN_ALARM(2),
+	SENSOR_ATTR_IN_ALARM(3),
+	SENSOR_ATTR_IN_ALARM(4),
+	SENSOR_ATTR_IN_ALARM(5),
+};
+
+#define SENSOR_ATTR_TEMP_INPUT(ix) \
+	SENSOR_ATTR_2(temp##ix##_input, S_IRUGO, \
+		show_temp, NULL, SHOW_TEMP_INPUT, ix-1)
+
+static struct sensor_device_attribute_2 vt1211_sysfs_temp_input[] = {
+	SENSOR_ATTR_TEMP_INPUT(1),
+	SENSOR_ATTR_TEMP_INPUT(2),
+	SENSOR_ATTR_TEMP_INPUT(3),
+	SENSOR_ATTR_TEMP_INPUT(4),
+	SENSOR_ATTR_TEMP_INPUT(5),
+	SENSOR_ATTR_TEMP_INPUT(6),
+	SENSOR_ATTR_TEMP_INPUT(7),
+};
+
+#define SENSOR_ATTR_TEMP_MAX(ix) \
+	SENSOR_ATTR_2(temp##ix##_max, S_IRUGO | S_IWUSR, \
+		show_temp, set_temp, SHOW_SET_TEMP_MAX, ix-1)
+
+static struct sensor_device_attribute_2 vt1211_sysfs_temp_max[] = {
+	SENSOR_ATTR_TEMP_MAX(1),
+	SENSOR_ATTR_TEMP_MAX(2),
+	SENSOR_ATTR_TEMP_MAX(3),
+	SENSOR_ATTR_TEMP_MAX(4),
+	SENSOR_ATTR_TEMP_MAX(5),
+	SENSOR_ATTR_TEMP_MAX(6),
+	SENSOR_ATTR_TEMP_MAX(7),
+};
+
+#define SENSOR_ATTR_TEMP_MAX_HYST(ix) \
+	SENSOR_ATTR_2(temp##ix##_max_hyst, S_IRUGO | S_IWUSR, \
+		show_temp, set_temp, SHOW_SET_TEMP_MAX_HYST, ix-1)
+
+static struct sensor_device_attribute_2 vt1211_sysfs_temp_max_hyst[] = {
+	SENSOR_ATTR_TEMP_MAX_HYST(1),
+	SENSOR_ATTR_TEMP_MAX_HYST(2),
+	SENSOR_ATTR_TEMP_MAX_HYST(3),
+	SENSOR_ATTR_TEMP_MAX_HYST(4),
+	SENSOR_ATTR_TEMP_MAX_HYST(5),
+	SENSOR_ATTR_TEMP_MAX_HYST(6),
+	SENSOR_ATTR_TEMP_MAX_HYST(7),
+};
+
+#define SENSOR_ATTR_TEMP_ALARM(ix) \
+	SENSOR_ATTR_2(temp##ix##_alarm, S_IRUGO, \
+		show_temp, NULL, SHOW_TEMP_ALARM, ix-1)
+
+static struct sensor_device_attribute_2 vt1211_sysfs_temp_alarm[] = {
+	SENSOR_ATTR_TEMP_ALARM(1),
+	SENSOR_ATTR_TEMP_ALARM(2),
+	SENSOR_ATTR_TEMP_ALARM(3),
+	SENSOR_ATTR_TEMP_ALARM(4),
+	SENSOR_ATTR_TEMP_ALARM(5),
+	SENSOR_ATTR_TEMP_ALARM(6),
+	SENSOR_ATTR_TEMP_ALARM(7),
+};
+
+#define SENSOR_ATTR_FAN(ix) \
+	SENSOR_ATTR_2(fan##ix##_input, S_IRUGO, \
+		show_fan, NULL, SHOW_FAN_INPUT, ix-1), \
+	SENSOR_ATTR_2(fan##ix##_min, S_IRUGO | S_IWUSR, \
+		show_fan, set_fan, SHOW_SET_FAN_MIN, ix-1), \
+	SENSOR_ATTR_2(fan##ix##_div, S_IRUGO | S_IWUSR, \
+		show_fan, set_fan, SHOW_SET_FAN_DIV, ix-1), \
+	SENSOR_ATTR_2(fan##ix##_alarm, S_IRUGO, \
+		show_fan, NULL, SHOW_FAN_ALARM, ix-1)
+
+#define SENSOR_ATTR_PWM(ix) \
+	SENSOR_ATTR_2(pwm##ix, S_IRUGO, \
+		show_pwm, NULL, SHOW_PWM, ix-1), \
+	SENSOR_ATTR_2(pwm##ix##_enable, S_IRUGO | S_IWUSR, \
+		show_pwm, set_pwm, SHOW_SET_PWM_ENABLE, ix-1), \
+	SENSOR_ATTR_2(pwm##ix##_auto_channels_temp, S_IRUGO | S_IWUSR, \
+		show_pwm, set_pwm, SHOW_SET_PWM_AUTO_CHANNELS_TEMP, ix-1)
+
+#define SENSOR_ATTR_PWM_FREQ(ix) \
+	SENSOR_ATTR_2(pwm##ix##_freq, S_IRUGO | S_IWUSR, \
+		show_pwm, set_pwm, SHOW_SET_PWM_FREQ, ix-1)
+
+#define SENSOR_ATTR_PWM_FREQ_RO(ix) \
+	SENSOR_ATTR_2(pwm##ix##_freq, S_IRUGO, \
+		show_pwm, NULL, SHOW_SET_PWM_FREQ, ix-1)
+
+#define SENSOR_ATTR_PWM_AUTO_POINT_TEMP(ix, ap) \
+	SENSOR_ATTR_2(pwm##ix##_auto_point##ap##_temp, S_IRUGO | S_IWUSR, \
+		show_pwm_auto_point_temp, set_pwm_auto_point_temp, \
+		ap-1, ix-1)
+
+#define SENSOR_ATTR_PWM_AUTO_POINT_TEMP_RO(ix, ap) \
+	SENSOR_ATTR_2(pwm##ix##_auto_point##ap##_temp, S_IRUGO, \
+		show_pwm_auto_point_temp, NULL, \
+		ap-1, ix-1)
+
+#define SENSOR_ATTR_PWM_AUTO_POINT_PWM(ix, ap) \
+	SENSOR_ATTR_2(pwm##ix##_auto_point##ap##_pwm, S_IRUGO | S_IWUSR, \
+		show_pwm_auto_point_pwm, set_pwm_auto_point_pwm, \
+		ap-1, ix-1)
+
+#define SENSOR_ATTR_PWM_AUTO_POINT_PWM_RO(ix, ap) \
+	SENSOR_ATTR_2(pwm##ix##_auto_point##ap##_pwm, S_IRUGO, \
+		show_pwm_auto_point_pwm, NULL, \
+		ap-1, ix-1)
+
+static struct sensor_device_attribute_2 vt1211_sysfs_fan_pwm[] = {
+	SENSOR_ATTR_FAN(1),
+	SENSOR_ATTR_FAN(2),
+	SENSOR_ATTR_PWM(1),
+	SENSOR_ATTR_PWM(2),
+	SENSOR_ATTR_PWM_FREQ(1),
+	SENSOR_ATTR_PWM_FREQ_RO(2),
+	SENSOR_ATTR_PWM_AUTO_POINT_TEMP(1, 1),
+	SENSOR_ATTR_PWM_AUTO_POINT_TEMP(1, 2),
+	SENSOR_ATTR_PWM_AUTO_POINT_TEMP(1, 3),
+	SENSOR_ATTR_PWM_AUTO_POINT_TEMP(1, 4),
+	SENSOR_ATTR_PWM_AUTO_POINT_TEMP_RO(2, 1),
+	SENSOR_ATTR_PWM_AUTO_POINT_TEMP_RO(2, 2),
+	SENSOR_ATTR_PWM_AUTO_POINT_TEMP_RO(2, 3),
+	SENSOR_ATTR_PWM_AUTO_POINT_TEMP_RO(2, 4),
+	SENSOR_ATTR_PWM_AUTO_POINT_PWM_RO(1, 1),
+	SENSOR_ATTR_PWM_AUTO_POINT_PWM(1, 2),
+	SENSOR_ATTR_PWM_AUTO_POINT_PWM(1, 3),
+	SENSOR_ATTR_PWM_AUTO_POINT_PWM_RO(1, 4),
+	SENSOR_ATTR_PWM_AUTO_POINT_PWM_RO(2, 1),
+	SENSOR_ATTR_PWM_AUTO_POINT_PWM(2, 2),
+	SENSOR_ATTR_PWM_AUTO_POINT_PWM(2, 3),
+	SENSOR_ATTR_PWM_AUTO_POINT_PWM_RO(2, 4),
+};
+
+static struct device_attribute vt1211_sysfs_misc[] = {
+	__ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm, set_vrm),
+	__ATTR(cpu0_vid, S_IRUGO, show_vid, NULL),
+	__ATTR(name, S_IRUGO, show_name, NULL),
+	__ATTR(alarms, S_IRUGO, show_alarms, NULL),
+};
+
+/* ---------------------------------------------------------------------
+ * Device registration and initialization
+ * --------------------------------------------------------------------- */
+
+static void __devinit vt1211_init_device(struct vt1211_data *data)
+{
+	/* set VRM */
+	data->vrm = vid_which_vrm();
+
+	/* Read (and initialize) UCH config */
+	data->uch_config = vt1211_read8(data, VT1211_REG_UCH_CONFIG);
+	if (uch_config > -1) {
+		data->uch_config = (data->uch_config & 0x83) |
+				   (uch_config << 2);
+		vt1211_write8(data, VT1211_REG_UCH_CONFIG, data->uch_config);
+	}
+
+	/* Initialize the interrupt mode (if request at module load time).
+	 * The VT1211 implements 3 different modes for clearing interrupts:
+	 * 0: Clear INT when status register is read. Regenerate INT as long
+	 *    as temp stays above hysteresis limit.
+	 * 1: Clear INT when status register is read. DON'T regenerate INT
+	 *    until temp falls below hysteresis limit and exceeds hot limit
+	 *    again.
+	 * 2: Clear INT when temp falls below max limit.
+	 *
+	 * The driver only allows to force mode 0 since that's the only one
+	 * that makes sense for 'sensors' */
+	if (int_mode == 0) {
+		vt1211_write8(data, VT1211_REG_TEMP1_CONFIG, 0);
+		vt1211_write8(data, VT1211_REG_TEMP2_CONFIG, 0);
+	}
+
+	/* Fill in some hard wired values into our data struct */
+	data->pwm_auto_pwm[0][3] = 255;
+	data->pwm_auto_pwm[1][3] = 255;
+}
+
+static void vt1211_remove_sysfs(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_in_input); i++) {
+		device_remove_file(dev,
+			&vt1211_sysfs_in_input[i].dev_attr);
+		device_remove_file(dev,
+			&vt1211_sysfs_in_min[i].dev_attr);
+		device_remove_file(dev,
+			&vt1211_sysfs_in_max[i].dev_attr);
+		device_remove_file(dev,
+			&vt1211_sysfs_in_alarm[i].dev_attr);
+	}
+	for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_temp_input); i++) {
+		device_remove_file(dev,
+			&vt1211_sysfs_temp_input[i].dev_attr);
+		device_remove_file(dev,
+			&vt1211_sysfs_temp_max[i].dev_attr);
+		device_remove_file(dev,
+			&vt1211_sysfs_temp_max_hyst[i].dev_attr);
+		device_remove_file(dev,
+			&vt1211_sysfs_temp_alarm[i].dev_attr);
+	}
+	for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_fan_pwm); i++) {
+		device_remove_file(dev,
+			&vt1211_sysfs_fan_pwm[i].dev_attr);
+	}
+	for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_misc); i++) {
+		device_remove_file(dev, &vt1211_sysfs_misc[i]);
+	}
+}
+
+static int __devinit vt1211_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct vt1211_data *data;
+	struct resource *res;
+	int i, err;
+
+	if (!(data = kzalloc(sizeof(struct vt1211_data), GFP_KERNEL))) {
+		err = -ENOMEM;
+		dev_err(dev, "Out of memory\n");
+		goto EXIT;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+	data->addr = res->start;
+	data->name = DRVNAME;
+	mutex_init(&data->update_lock);
+
+	platform_set_drvdata(pdev, data);
+
+	/* Initialize the VT1211 chip */
+	vt1211_init_device(data);
+
+	/* Create sysfs interface files */
+	for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_in_input); i++) {
+		if (ISVOLT(i, data->uch_config)) {
+			if ((err = device_create_file(dev,
+				&vt1211_sysfs_in_input[i].dev_attr)) ||
+			    (err = device_create_file(dev,
+				&vt1211_sysfs_in_min[i].dev_attr)) ||
+			    (err = device_create_file(dev,
+				&vt1211_sysfs_in_max[i].dev_attr)) ||
+			    (err = device_create_file(dev,
+				&vt1211_sysfs_in_alarm[i].dev_attr))) {
+				goto EXIT_DEV_REMOVE;
+			}
+		}
+	}
+	for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_temp_input); i++) {
+		if (ISTEMP(i, data->uch_config)) {
+			if ((err = device_create_file(dev,
+				&vt1211_sysfs_temp_input[i].dev_attr)) ||
+			    (err = device_create_file(dev,
+				&vt1211_sysfs_temp_max[i].dev_attr)) ||
+			    (err = device_create_file(dev,
+				&vt1211_sysfs_temp_max_hyst[i].dev_attr)) ||
+			    (err = device_create_file(dev,
+				&vt1211_sysfs_temp_alarm[i].dev_attr))) {
+				goto EXIT_DEV_REMOVE;
+			}
+		}
+	}
+	for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_fan_pwm); i++) {
+		err = device_create_file(dev,
+			&vt1211_sysfs_fan_pwm[i].dev_attr);
+		if (err) {
+			goto EXIT_DEV_REMOVE;
+		}
+	}
+	for (i = 0; i < ARRAY_SIZE(vt1211_sysfs_misc); i++) {
+		err = device_create_file(dev,
+		       &vt1211_sysfs_misc[i]);
+		if (err) {
+			goto EXIT_DEV_REMOVE;
+		}
+	}
+
+	/* Register device */
+	data->class_dev = hwmon_device_register(dev);
+	if (IS_ERR(data->class_dev)) {
+		err = PTR_ERR(data->class_dev);
+		dev_err(dev, "Class registration failed (%d)\n", err);
+		goto EXIT_DEV_REMOVE_SILENT;
+	}
+
+	return 0;
+
+EXIT_DEV_REMOVE:
+	dev_err(dev, "Sysfs interface creation failed (%d)\n", err);
+EXIT_DEV_REMOVE_SILENT:
+	vt1211_remove_sysfs(pdev);
+	platform_set_drvdata(pdev, NULL);
+	kfree(data);
+EXIT:
+	return err;
+}
+
+static int __devexit vt1211_remove(struct platform_device *pdev)
+{
+	struct vt1211_data *data = platform_get_drvdata(pdev);
+
+	hwmon_device_unregister(data->class_dev);
+	vt1211_remove_sysfs(pdev);
+	platform_set_drvdata(pdev, NULL);
+	kfree(data);
+
+	return 0;
+}
+
+static struct platform_driver vt1211_driver = {
+	.driver = {
+		.owner = THIS_MODULE,
+		.name  = DRVNAME,
+	},
+	.probe  = vt1211_probe,
+	.remove = __devexit_p(vt1211_remove),
+};
+
+static int __init vt1211_device_add(unsigned short address)
+{
+	struct resource res = {
+		.start	= address,
+		.end	= address + 0x7f,
+		.flags	= IORESOURCE_IO,
+	};
+	int err;
+
+	pdev = platform_device_alloc(DRVNAME, address);
+	if (!pdev) {
+		err = -ENOMEM;
+		printk(KERN_ERR DRVNAME ": Device allocation failed (%d)\n",
+		       err);
+		goto EXIT;
+	}
+
+	res.name = pdev->name;
+	err = platform_device_add_resources(pdev, &res, 1);
+	if (err) {
+		printk(KERN_ERR DRVNAME ": Device resource addition failed "
+		       "(%d)\n", err);
+		goto EXIT_DEV_PUT;
+	}
+
+	err = platform_device_add(pdev);
+	if (err) {
+		printk(KERN_ERR DRVNAME ": Device addition failed (%d)\n",
+		       err);
+		goto EXIT_DEV_PUT;
+	}
+
+	return 0;
+
+EXIT_DEV_PUT:
+	platform_device_put(pdev);
+EXIT:
+	return err;
+}
+
+static int __init vt1211_find(unsigned short *address)
+{
+	int err = -ENODEV;
+
+	superio_enter();
+
+	if (superio_inb(SIO_VT1211_DEVID) != SIO_VT1211_ID) {
+		goto EXIT;
+	}
+
+	superio_select(SIO_VT1211_LDN_HWMON);
+
+	if ((superio_inb(SIO_VT1211_ACTIVE) & 1) == 0) {
+		printk(KERN_WARNING DRVNAME ": HW monitor is disabled, "
+		       "skipping\n");
+		goto EXIT;
+	}
+
+	*address = ((superio_inb(SIO_VT1211_BADDR) << 8) |
+		    (superio_inb(SIO_VT1211_BADDR + 1))) & 0xff00;
+	if (*address == 0) {
+		printk(KERN_WARNING DRVNAME ": Base address is not set, "
+		       "skipping\n");
+		goto EXIT;
+	}
+
+	err = 0;
+	printk(KERN_INFO DRVNAME ": Found VT1211 chip at 0x%04x, "
+	       "revision %u\n", *address, superio_inb(SIO_VT1211_DEVREV));
+
+EXIT:
+	superio_exit();
+	return err;
+}
+
+static int __init vt1211_init(void)
+{
+	int err;
+	unsigned short address = 0;
+
+	err = vt1211_find(&address);
+	if (err) {
+		goto EXIT;
+	}
+
+	if ((uch_config < -1) || (uch_config > 31)) {
+		err = -EINVAL;
+		printk(KERN_WARNING DRVNAME ": Invalid UCH configuration %d. "
+		       "Choose a value between 0 and 31.\n", uch_config);
+	  goto EXIT;
+	}
+
+	if ((int_mode < -1) || (int_mode > 0)) {
+		err = -EINVAL;
+		printk(KERN_WARNING DRVNAME ": Invalid interrupt mode %d. "
+		       "Only mode 0 is supported.\n", int_mode);
+	  goto EXIT;
+	}
+
+	err = platform_driver_register(&vt1211_driver);
+	if (err) {
+		goto EXIT;
+	}
+
+	/* Sets global pdev as a side effect */
+	err = vt1211_device_add(address);
+	if (err) {
+		goto EXIT_DRV_UNREGISTER;
+	}
+
+	return 0;
+
+EXIT_DRV_UNREGISTER:
+	platform_driver_unregister(&vt1211_driver);
+EXIT:
+	return err;
+}
+
+static void __exit vt1211_exit(void)
+{
+	platform_device_unregister(pdev);
+	platform_driver_unregister(&vt1211_driver);
+}
+
+MODULE_AUTHOR("Juerg Haefliger <juergh at gmail.com>");
+MODULE_DESCRIPTION("VT1211 sensors");
+MODULE_LICENSE("GPL");
+
+module_init(vt1211_init);
+module_exit(vt1211_exit);


Patches currently in gregkh-2.6 which might be from khali at linux-fr.org are

i2c/hwmon-w83627ehf-add-pwm-support.patch
i2c/hwmon-w83627ehf-documentation.patch
i2c/hwmon-k8temp-documentation.patch
i2c/hwmon-abituguru-suspend-resume.patch
i2c/hwmon-individual-alarm-files-1.patch
i2c/hwmon-kconfig-update.patch
i2c/hwmon-it87-disabled-fans.patch
i2c/hwmon-remove-yuan-mu-address.patch
i2c/hwmon-unchecked-return-status-fixes-1.patch
i2c/hwmon-unchecked-return-status-fixes-2.patch
i2c/hwmon-unchecked-return-status-fixes-3.patch
i2c/hwmon-unchecked-return-status-fixes-4.patch
i2c/hwmon-unchecked-return-status-fixes-5.patch
i2c/hwmon-unchecked-return-status-fixes-6.patch
i2c/hwmon-unchecked-return-status-fixes-pc87360-1.patch
i2c/hwmon-unchecked-return-status-fixes-pc87360-2.patch
i2c/hwmon-unchecked-return-status-fixes-pc87360-3.patch
i2c/hwmon-unchecked-return-status-fixes-smsc.patch
i2c/hwmon-unchecked-return-status-fixes-vt8231.patch
i2c/hwmon-atxp1-signed-unsigned-char-bug.patch
i2c/hwmon-hdaps-handle-errors-from-input-register-device.patch
i2c/hwmon-it87-copyright-update.patch
i2c/hwmon-it87-div-to-reg-overflow.patch
i2c/hwmon-it87-in8-no-limits.patch
i2c/hwmon-it87-it8716f-support.patch
i2c/hwmon-it87-it8718f-support.patch
i2c/hwmon-it87-sane-limit-defaults.patch
i2c/hwmon-it87-set-fan-div.patch
i2c/hwmon-k8temp-autoload.patch
i2c/hwmon-k8temp-new-driver.patch
i2c/hwmon-smsc47m1-fix-dev-message.patch
i2c/hwmon-unchecked-return-status-fixes-w83627ehf.patch
i2c/hwmon-unchecked-return-status-fixes-w83781d.patch
i2c/hwmon-unchecked-return-status-fixes-w83792d.patch
i2c/hwmon-unchecked-return-status-fixes-w83l785ts.patch
i2c/hwmon-vt1211-add-module-parameters-description.patch
i2c/hwmon-vt1211-documentation.patch
i2c/hwmon-vt1211-new-driver.patch
i2c/hwmon-w83791d-doc-update.patch
driver-class/i2c-dev-device.patch
driver-class/i2c-dev-device.old.patch




More information about the lm-sensors mailing list