[lm-sensors] Asus P5B Deluxe / Winbond 83627DHG

[Joe Harvell]

Rudolf Marek wrote:
>
>> temp2):  Under load, my temp3 *drops* from 119 to 103.5 under load and 
>> then goes back up afterwards ?????
>>     
>
> Hmm my MB has this at 127C which means unconnected. Please can you send a
> dsdt.bin file? (cat /proc/acpi/dsdt > /tmp/dsdt.bin)
>   
This machine is powered down right now.  I'll send this shortly.
>   
>> fan1: (you state it should be the CPU_FAN) The RPM in the 1100 range 
>> matches what I'm seeing in the BIOS for CHA_FAN1 and CHA_FAN2 (both are 
>> documented to run at 1800 RPM)
>>     
>
> ok
>
>   
>> fan2: (you state it should be CHA_FAN1) The RPM of 2537 is consistent 
>> with what I'm seeing in the BIOS for CPU_FAN (a Zalman CNPS9500 LED)
>> fan3: (you state it should be CHA_FAN2) My fan3 shows 0, but I have 
>> verified both fans are spinning and connected to CHA_FAN1 and CHA_FAN2
>> fan4: (you state this is PWR_FAN):  The P5B manual states that this 
>> connector is not supported by their QFan2 software monitoring.  I doubt 
>> it would be monitorable.
>>     
>
> Hmm how many/what fans can you see in the BIOS?
>   
I'll get that shortly also.  Just wanted to let you know that I see some 
strange behavior of lm_sensors with respect to the fan5.  This sensor 
usually reports zero.  But after it has been up for a while it starts 
reporting something in the 1100 to 1200 range.  This is consistent with 
my case fan speed.  So it seems fan5 is either CHA_FAN1 or CHA_FAN2.  
Actually, I can't confirm it's the fan5 sensor that's doing this.  That 
is what I remember from a couple of days ago.  But I updated my 
sensors.conf file to put a label on the sensor that was doing this, so 
once I power up my machine again, I'll verify this as well.
> here is my:
>
> axon:~# sensors
> w83627dhg-isa-0290
> Adapter: ISA adapter
> VCore:     +1.14 V  (min =  +0.00 V, max =  +1.74 V)
> in1:      +12.30 V  (min =  +0.26 V, max = +10.88 V) ALARM
> AVCC:      +3.25 V  (min =  +1.74 V, max =  +2.24 V) ALARM
> 3VCC:      +3.25 V  (min =  +3.44 V, max =  +3.17 V) ALARM
> in4:       +1.11 V  (min =  +1.17 V, max =  +0.26 V) ALARM
> in5:       +1.59 V  (min =  +0.06 V, max =  +1.54 V) ALARM
> in6:       +3.53 V  (min =  +0.51 V, max =  +1.00 V) ALARM
> VSB:       +3.25 V  (min =  +1.74 V, max =  +3.66 V)
> VBAT:      +3.25 V  (min =  +0.05 V, max =  +0.64 V) ALARM
> Case Fan:    0 RPM  (min = 21093 RPM, div = 64) ALARM
> CPU Fan:  1687 RPM  (min = 1662 RPM, div = 4)
> Aux Fan:     0 RPM  (min = 10546 RPM, div = 64) ALARM
> fan4:        0 RPM  (min = 10546 RPM, div = 32) ALARM
> fan5:     3835 RPM  (min = 7670 RPM, div = 2) ALARM
> Sys Temp:    +33°C  (high =   -56°C, hyst =   +39°C)
> CPU Temp:  +39.5°C  (high = +80.0°C, hyst = +75.0°C)
> AUX Temp: +127.0°C  (high = +80.0°C, hyst = +75.0°C)   ALARM
>
> coretemp-isa-0000
> Adapter: ISA adapter
> temp1:       +30°C  (high =   +85°C)
>
> coretemp-isa-0001
> Adapter: ISA adapter
> temp1:       +32°C  (high =   +85°C)
>
> Rudolf
>   
I forget, is your board a P5B Deluxe WiFi?