[lm-sensors] Asus P5B Deluxe / Winbond 83627DHG

[Rudolf Marek]

Hello again

Sorry for the delay.
> I figured out why I got zero readings for fan5.  Since my case fans are 
> lower speed, it seems the divisor was to low.  I remedied this by 
> settting fan1_min and fan5_min to 700.  This also has the side effect of 
> setting the divisor to 16.  Now I get readings in the 1100 RPM range for 
> both fan1 and fan5.

Ok. That explains it.

> Here is what I see in the BIOS Hardware Monitor after being on for about 
> 5 minutes:
> 
> CPU Temperature          35.5 C
> MB Temperature           21 C
> CPU Fan Speed            2556
> CPU QFan Control         Enabled
> CPU Fan Profile          Optimal
> Chassis Fan1 Speed       1095
> Chassis Fan2 Speed       1163
> Chassis Fan3 Speed       N/A
> Chassis QFan Control     Enabled
> Chassis Fan Profile      Optimal
> Power Fan Speed          N/A
> 
> VCore Voltage             1.176
> 3.3V Voltage              3.328
> 5V Voltage                4.992
> 12V Voltage              12.144
> 
> Here is my Idle sensors output
> 
> jharvell at cujo ~ $ sensors
> w83627dhg-isa-0290
> Adapter: ISA adapter
> VCore:     +1.12 V  (min =  +0.00 V, max =  +1.74 V)
> 12 V:     +12.14 V  (min = +10.82 V, max = +13.20 V)
> 3.3V:      +3.33 V  (min =  +3.14 V, max =  +3.47 V)
> 5V:        +5.04 V  (min =  +4.76 V, max =  +5.25 V)
> VSB:       +3.33 V  (min =  +3.14 V, max =  +3.47 V)
> CHA_FAN1: 1125 RPM  (min =  703 RPM, div = 16)
> CPU_FAN:  2518 RPM  (min = 1704 RPM, div = 8)
> CHA_FAN2: 1222 RPM  (min =  703 RPM, div = 16)
> Sys Temp:    +28 C  (high =   +40 C, hyst =   +35 C)
> CPU Temp:  +34.5 C  (high = +55.0 C, hyst = +45.0 C)
> 
> Actually, I recently finished a compile, so it may still be cooling 
> slightly.  Also, I am using CPU Frequency scaling.  So the CPU is at 
> 1.60 GHz instead of the normal 2.39 GHz.  I don't know what the 
> operating CPU frequency is in the BIOS.
> 
> jharvell at cujo ~ $ cpufreq-info
> cpufrequtils 002: cpufreq-info (C) Dominik Brodowski 2004-2006
> Report errors and bugs to linux at brodo.de, please.
> analyzing CPU 0:
>   driver: centrino
>   CPUs which need to switch frequency at the same time: 0
>   hardware limits: 1.60 GHz - 2.39 GHz
>   available frequency steps: 2.39 GHz, 1.60 GHz
>   available cpufreq governors: ondemand, performance
>   current policy: frequency should be within 1.60 GHz and 2.39 GHz.
>                   The governor "ondemand" may decide which speed to use
>                   within this range.
>   current CPU frequency is 1.60 GHz.
> analyzing CPU 1:
>   driver: centrino
>   CPUs which need to switch frequency at the same time: 1
>   hardware limits: 1.60 GHz - 2.39 GHz
>   available frequency steps: 2.39 GHz, 1.60 GHz
>   available cpufreq governors: ondemand, performance
>   current policy: frequency should be within 1.60 GHz and 2.39 GHz.
>                   The governor "ondemand" may decide which speed to use
>                   within this range.
>   current CPU frequency is 1.60 GHz.

Maybe you can also try the coretemp driver if the CPU is pentium M or Core series.

Rudolf