[lm-sensors] Abit AT8 (non-32X) / Winbond 83627EHF

[Rick Wright]

David,

Thanks for the advice.  Tried the set fanX_min 0 commands below.  There 
was no change in behavior.  All fan RPM's still reported as 0.  Any 
other ideas?

Thanks,
Rick

David Hubbard wrote:

> Hi Rick,
>
> The 0 RPM fan speeds are probably due to the minimum fan speed limits
> for triggering the alarms. To be brief, add something like this to
> your sensors.conf:
>
> set fan1_min 0
> set fan2_min 0
> set fan3_min 0
> set fan4_min 0
> set fan5_min 0
>
> (Note that after you do this, you have changed what will trigger an
> alarm. You should check that your system does not overheat.)
>
> This should get the driver to look "low enough" to find your fan RPM.
> You can then modify sensors.conf to have a reasonable minimum for your
> fans, or possible even ignore alarms generated by your fans.
>
> Hope that helps,
> David
>
> On 2/12/07, Rick Wright <riwright at vt.edu> wrote:
>
>> Rick Wright wrote:
>>
>> >Hello list,
>> >
>> >I have the Abit AT8 mobo described in the subject line and I'm 
>> trying to
>> >get lm_sensors working properly for this board.  I see there is still
>> >very recent activity concerning getting this Winbond chip fully
>> >supported.  In the latest 2.10.2 release I see Dave Platt added these
>> >changes relavent to my board:
>> >
>> >Program sensord:
>> >                        Add w83627ehf voltage support (Dave Platt)
>> >                        Add k8temp support (Dave Platt)
>> >
>> >These additions appear to be working properly OOTB as the "sensors"
>> >command produces the following output:
>> >
>> >[riwright at box ~]$ sensors
>> >k8temp-pci-00c3
>> >Adapter: PCI adapter
>> >Core0 Temp:
>> >             +45 °C
>> >Core1 Temp:
>> >             +46 °C
>> >
>> >w83627ehf-isa-0290
>> >Adapter: ISA adapter
>> >VCore:     +2.04 V  (min =  +0.00 V, max =  +1.74 V) ALARM
>> >in1:      +13.46 V  (min = +13.46 V, max = +12.36 V) ALARM
>> >AVCC:      +3.22 V  (min =  +3.02 V, max =  +4.08 V)
>> >3VCC:      +3.22 V  (min =  +3.92 V, max =  +3.82 V) ALARM
>> >in4:       +1.66 V  (min =  +2.01 V, max =  +1.01 V) ALARM
>> >in5:       +1.66 V  (min =  +1.16 V, max =  +0.95 V) ALARM
>> >in6:       +5.32 V  (min =  +6.53 V, max =  +6.32 V) ALARM
>> >VSB:       +3.07 V  (min =  +4.08 V, max =  +3.06 V) ALARM
>> >VBAT:      +2.16 V  (min =  +2.02 V, max =  +2.38 V)
>> >in9:       +1.56 V  (min =  +1.98 V, max =  +1.75 V) ALARM
>> >Case Fan:    0 RPM  (min = 1318 RPM, div = 128) ALARM
>> >CPU Fan:     0 RPM  (min = 1757 RPM, div = 128) ALARM
>> >Aux Fan:     0 RPM  (min = 10546 RPM, div = 128) ALARM
>> >fan4:        0 RPM  (min = 10546 RPM, div = 128) ALARM
>> >fan5:        0 RPM  (min = 168750 RPM, div = 8) ALARM
>> >Sys Temp:    -48 °C  (high =   +45 °C, hyst =   +40 °C)
>> >CPU Temp:  -48.0 °C  (high = +45.0 °C, hyst = +40.0 °C)
>> >AUX Temp:  -48.0 °C  (high = +80.0 °C, hyst = +75.0 °C)
>> >
>> >
>> >So, as advertized, the Voltage support seems to be working.  However,
>> >the fan speeds and temperatures do not.  Are these items currently
>> >supported yet?  Or do I have a configuration problem?  If not yet
>> >supported, is this planned for the future?
>> >
>> >Any input/hints/pointers greatly appreciated.
>> >
>> >Thanks,
>> >Rick
>> >
>> >_______________________________________________
>> >lm-sensors mailing list
>> >lm-sensors at lm-sensors.org
>> >http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
>> >
>> >
>> >
>>
>>
>> _______________________________________________
>> lm-sensors mailing list
>> lm-sensors at lm-sensors.org
>> http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
>>
>