[lm-sensors] Abit AT8 (non-32X) / Winbond 83627EHF

[David Hubbard]

Hi Rick,

Did the dividers change? In your previous email, they are all 128.

David

On 2/13/07, Rick Wright <riwright at vt.edu> wrote:
> David,
>
> Thanks for the advice.  Tried the set fanX_min 0 commands below.  There
> was no change in behavior.  All fan RPM's still reported as 0.  Any
> other ideas?
>
> Thanks,
> Rick
>
> David Hubbard wrote:
>
> > Hi Rick,
> >
> > The 0 RPM fan speeds are probably due to the minimum fan speed limits
> > for triggering the alarms. To be brief, add something like this to
> > your sensors.conf:
> >
> > set fan1_min 0
> > set fan2_min 0
> > set fan3_min 0
> > set fan4_min 0
> > set fan5_min 0
> >
> > (Note that after you do this, you have changed what will trigger an
> > alarm. You should check that your system does not overheat.)
> >
> > This should get the driver to look "low enough" to find your fan RPM.
> > You can then modify sensors.conf to have a reasonable minimum for your
> > fans, or possible even ignore alarms generated by your fans.
> >
> > Hope that helps,
> > David
> >
> > On 2/12/07, Rick Wright <riwright at vt.edu> wrote:
> >
> >> Rick Wright wrote:
> >>
> >> >Hello list,
> >> >
> >> >I have the Abit AT8 mobo described in the subject line and I'm
> >> trying to
> >> >get lm_sensors working properly for this board.  I see there is still
> >> >very recent activity concerning getting this Winbond chip fully
> >> >supported.  In the latest 2.10.2 release I see Dave Platt added these
> >> >changes relavent to my board:
> >> >
> >> >Program sensord:
> >> >                        Add w83627ehf voltage support (Dave Platt)
> >> >                        Add k8temp support (Dave Platt)
> >> >
> >> >These additions appear to be working properly OOTB as the "sensors"
> >> >command produces the following output:
> >> >
> >> >[riwright at box ~]$ sensors
> >> >k8temp-pci-00c3
> >> >Adapter: PCI adapter
> >> >Core0 Temp:
> >> >             +45 °C
> >> >Core1 Temp:
> >> >             +46 °C
> >> >
> >> >w83627ehf-isa-0290
> >> >Adapter: ISA adapter
> >> >VCore:     +2.04 V  (min =  +0.00 V, max =  +1.74 V) ALARM
> >> >in1:      +13.46 V  (min = +13.46 V, max = +12.36 V) ALARM
> >> >AVCC:      +3.22 V  (min =  +3.02 V, max =  +4.08 V)
> >> >3VCC:      +3.22 V  (min =  +3.92 V, max =  +3.82 V) ALARM
> >> >in4:       +1.66 V  (min =  +2.01 V, max =  +1.01 V) ALARM
> >> >in5:       +1.66 V  (min =  +1.16 V, max =  +0.95 V) ALARM
> >> >in6:       +5.32 V  (min =  +6.53 V, max =  +6.32 V) ALARM
> >> >VSB:       +3.07 V  (min =  +4.08 V, max =  +3.06 V) ALARM
> >> >VBAT:      +2.16 V  (min =  +2.02 V, max =  +2.38 V)
> >> >in9:       +1.56 V  (min =  +1.98 V, max =  +1.75 V) ALARM
> >> >Case Fan:    0 RPM  (min = 1318 RPM, div = 128) ALARM
> >> >CPU Fan:     0 RPM  (min = 1757 RPM, div = 128) ALARM
> >> >Aux Fan:     0 RPM  (min = 10546 RPM, div = 128) ALARM
> >> >fan4:        0 RPM  (min = 10546 RPM, div = 128) ALARM
> >> >fan5:        0 RPM  (min = 168750 RPM, div = 8) ALARM
> >> >Sys Temp:    -48 °C  (high =   +45 °C, hyst =   +40 °C)
> >> >CPU Temp:  -48.0 °C  (high = +45.0 °C, hyst = +40.0 °C)
> >> >AUX Temp:  -48.0 °C  (high = +80.0 °C, hyst = +75.0 °C)
> >> >
> >> >
> >> >So, as advertized, the Voltage support seems to be working.  However,
> >> >the fan speeds and temperatures do not.  Are these items currently
> >> >supported yet?  Or do I have a configuration problem?  If not yet
> >> >supported, is this planned for the future?
> >> >
> >> >Any input/hints/pointers greatly appreciated.
> >> >
> >> >Thanks,
> >> >Rick
> >> >
> >> >_______________________________________________
> >> >lm-sensors mailing list
> >> >lm-sensors at lm-sensors.org
> >> >http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
> >> >
> >> >
> >> >
> >>
> >>
> >> _______________________________________________
> >> lm-sensors mailing list
> >> lm-sensors at lm-sensors.org
> >> http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
> >>
> >
>