[lm-sensors] Activate WD chip on Tyan S7025?

Carsten Aulbert carsten.aulbert at aei.mpg.de
Mon Mar 1 14:47:17 CET 2010


Hi

On Monday 01 March 2010 14:19:35 Jean Delvare wrote:
> Yes there is, but in 99% of the cases, disabled sensors in Super-I/O
> chips are disabled because they are not used, so enabling them will no
> lead you anywhere. You can load the w83627ehf driver and it will enable
> the sensors for you, but chances are that the output of "sensors" will
> be full of zeroes or otherwise meaningless values.

Ah ok, I just should have tried it then:

# modprobe w83627ehf
# dmesg|tail
[...]
[22940.891889] w83627ehf: Forcibly enabling Super-I/O. Sensor is probably 
unusable. 
[22940.932286] w83627ehf: Found W83627DHG-P chip at 0xa10 
# sensors -s
# sensors 
coretemp-isa-0000 
Adapter: ISA adapter
Core 0:      +39.0°C  (high = +90.0°C, crit = +100.0°C)  

coretemp-isa-0001
Adapter: ISA adapter
Core 1:      +33.0°C  (high = +90.0°C, crit = +100.0°C)  

coretemp-isa-0002
Adapter: ISA adapter
Core 2:      +39.0°C  (high = +90.0°C, crit = +100.0°C)  

coretemp-isa-0003
Adapter: ISA adapter
Core 3:      +34.0°C  (high = +90.0°C, crit = +100.0°C)  

w83627dhg-isa-0a10
Adapter: ISA adapter
Vcore:       +0.00 V  (min =  +0.00 V, max =  +1.74 V)   
in1:         +0.00 V  (min =  +1.68 V, max =  +1.22 V)   ALARM
AVCC:        +3.34 V  (min =  +2.98 V, max =  +3.63 V)        
VCC:         +3.34 V  (min =  +2.98 V, max =  +3.63 V)        
in4:         +1.54 V  (min =  +2.02 V, max =  +1.22 V)   ALARM
in5:         +0.00 V  (min =  +1.54 V, max =  +1.54 V)   ALARM
in6:         +1.15 V  (min =  +1.58 V, max =  +0.29 V)   ALARM
3VSB:        +3.33 V  (min =  +2.98 V, max =  +3.63 V)
Vbat:        +3.26 V  (min =  +2.70 V, max =  +3.30 V)
fan1:          0 RPM  (min = 5273 RPM, div = 4)  ALARM
fan2:          0 RPM  (min = 21093 RPM, div = 4)  ALARM
fan3:          0 RPM  (min = 3590 RPM, div = 4)  ALARM
fan4:          0 RPM  (min = 61363 RPM, div = 2)  ALARM
fan5:          0 RPM  (min = 56250 RPM, div = 2)  ALARM
temp1:       +28.0°C  (high = +62.0°C, hyst = +34.0°C)  sensor = thermistor
temp2:      +127.5°C  (high = +80.0°C, hyst = +75.0°C)  ALARM  sensor = diode
temp3:       +31.5°C  (high = +80.0°C, hyst = +75.0°C)  sensor = thermistor
cpu0_vid:   +2.050 V


Looks, ok-ish but not perfect ;)

We'll see what we can make from this.

Thanks a lot!

Carsten

PS: 
ipmitool still lacks any reading, 

# ipmitool sdr
CPU0 below Tmax  | no reading        | ns
CPU1 below Tmax  | disabled          | ns
RT3              | no reading        | ns
RT4              | no reading        | ns
RT5              | no reading        | ns
CPU0 VCORE       | no reading        | ns
CPU1 VCORE       | disabled          | ns
CPU0 VTT         | no reading        | ns
CPU1 VTT         | disabled          | ns
5V               | no reading        | ns
5V SB            | no reading        | ns
12V              | no reading        | ns
3V               | no reading        | ns
VBAT             | no reading        | ns
IOH 1.1V         | no reading        | ns
ICH 1.5V         | no reading        | ns
CPU0 DDR3 1.5V   | no reading        | ns
CPU1 DDR3 1.5V   | disabled          | ns
CPU0 FAN         | no reading        | ns
CPU1 FAN         | disabled          | ns
REAR FAN1        | no reading        | ns
REAR FAN2        | no reading        | ns
FRONT FAN1       | no reading        | ns
FRONT FAN2       | no reading        | ns
FRONT FAN3       | no reading        | ns
Power1           | no reading        | ns





More information about the lm-sensors mailing list