[lm-sensors] [PATCHv2] hwmon: lis3: Short explanations of platform data fields

[Éric Piel]

Op 23-10-10 15:39, Samu Onkalo schreef:
> Short documentation at kernel doc format.
>
> Signed-off-by: Samu Onkalo<samu.p.onkalo at nokia.com>
Acked-by: Eric Piel <eric.piel at tremplin-utc.net>
> ---
>   include/linux/lis3lv02d.h |   46 +++++++++++++++++++++++++++++++++++++++++++++
>   1 files changed, 46 insertions(+), 0 deletions(-)
>
> diff --git a/include/linux/lis3lv02d.h b/include/linux/lis3lv02d.h
> index c949612..d4292c8 100644
> --- a/include/linux/lis3lv02d.h
> +++ b/include/linux/lis3lv02d.h
> @@ -1,6 +1,52 @@
>   #ifndef __LIS3LV02D_H_
>   #define __LIS3LV02D_H_
>
> +/**
> + * struct lis3lv02d_platform_data - lis3 chip family platform data
> + * @click_flags:	Click detection unit configuration
> + * @click_thresh_x:	Click detection unit x axis threshold
> + * @click_thresh_y:	Click detection unit y axis threshold
> + * @click_thresh_z:	Click detection unit z axis threshold
> + * @click_time_limit:	Click detection unit time parameter
> + * @click_latency:	Click detection unit latency parameter
> + * @click_window:	Click detection unit window parameter
> + * @irq_cfg:		On chip irq source and type configuration (click /
> + *			data available / wake up, open drain, polarity)
> + * @irq_flags1:		Additional irq triggering flags for irq channel 0
> + * @irq_flags2:		Additional irq triggering flags for irq channel 1
> + * @duration1:		Wake up unit 1 duration parameter
> + * @duration2:		Wake up unit 2 duration parameter
> + * @wakeup_flags:	Wake up unit 1 flags
> + * @wakeup_thresh:	Wake up unit 1 threshold value
> + * @wakeup_flags2:	Wake up unit 2 flags
> + * @wakeup_thresh2:	Wake up unit 2 threshold value
> + * @hipass_ctrl:	High pass filter control (enable / disable, cut off
> + *			frequency)
> + * @axis_x:		Sensor orientation remapping for x-axis
> + * @axis_y:		Sensor orientation remapping for y-axis
> + * @axis_z:		Sensor orientation remapping for z-axis
> + * @driver_features:	Enable bits for different features. Disabled by default
> + * @default_rate:	Default sampling rate. 0 means reset default
> + * @setup_resources:	Interrupt line setup call back function
> + * @release_resources:	Interrupt line release call back function
> + * @st_min_limits[3]:	Selftest acceptance minimum values
> + * @st_max_limits[3]:	Selftest acceptance maximum values
> + * @irq2:		Irq line 2 number
> + *
> + * Platform data is used to setup the sensor chip. Meaning of the different
> + * chip features can be found from the data sheet. It is publicly available
> + * at www.st.com web pages. Currently the platform data is used
> + * only for the 8 bit device. The 8 bit device has two wake up / free fall
> + * detection units and click detection unit. There are plenty of ways to
> + * configure the chip which makes is quite hard to explain deeper meaning of
> + * the fields here. Behaviour of the detection blocks varies heavily depending
> + * on the configuration. For example, interrupt detection block can use high
> + * pass filtered data which makes it react to the changes in the acceleration.
> + * Irq_flags can be used to enable interrupt detection on the both edges.
> + * With proper chip configuration this produces interrupt when some trigger
> + * starts and when it goes away.
> + */
> +
>   struct lis3lv02d_platform_data {
>   	/* please note: the 'click' feature is only supported for
>   	 * LIS[32]02DL variants of the chip and will be ignored for